Archive for the ‘ฺBasic Computer Troubleshooting’ Category

15 January, 2010

Troubleshooting tips and techniques gathered printer part IV


Problem with the printer also has several issues that need a computer repairman problem. Troubleshooting the printer must know why and to resolve correctly to the printer to work again. Today I will talk about Troubleshooting tips and techniques gathered printer part IV

Small text wrong.

Most printers will have utility for managing system to print. And tend to care issues. Of the type that almost. If you print a font, but little unusual though. Not resize the word no. To check that the Print Preference or utility see what adjustments or special mode. Or a brief automated custom font or not? Adjusted to a value that can be printed normally.

Print text missing but not fully displayed.

This problem occurs both in the text flowing other. And print images. Cause it comes from setting the building-block type invalid as a certain font. Or of the line on the last line to the extreme. This means that the setting does not meet building-block. The problem can be from a program that you use in that time, such as Acrobat, Word, Excel and other programs. When setting the type and settings page, try another test print.

Print documents but clearly about to close the back hatch gray.

Typically, the only complete print text or other line that will clear the table and then back around to close the hatch paper should not be any other color. Unless the white meat of the paper. But if it becomes a new color from gray. Gray scale-like mode, then each is. Review paper, so that is the type or empty? Try and visit the utility of that type is Set to close the back hatch about what color it is or not? If everything is normal living to tell the. To assume that Otnenars or drum cartridge may be damaged.

Print or font is any point in space inside.

Caused by the setting does not match the paper type used. Or vice versa, the paper that it does not match the value type to be selected.

Printing to a tilt Oigeig not match.

Check the paper tray that you enter or paste the paper straight. If you put tight or stiff paper does not match rail Printing. Time into the paper feed roller, it would not meet with visiting. Lost time as print on paper is not correct. Paper because it does not match.

White vertical line happen.

Met with the small print with white thread Pak linear space of some silk. In fact, not a white ink. But the gap is small. Into the ink is not sure enough. And symptoms that are caused by more than one. Since Otnenars and drum are dirty stains. Misuse, such as paper, paper with a laser-based, it is not. If they could print out the results this has. In addition, within what may be obscure glass to reflect the laser show in the style vertical length. Cause symptoms come out in this manner.

Hold the paper tray is not a good long time.

Printer does not print often. There may be many problems when returning to work again. One of them is the quality of paper that could lose as if you put paper in the tray is long. Also include the full bonus points with. The left behind by all without typing. Paper they will be together with moisture in the room. Or if the device placed in a high temperature paper will take a simple framework. Print quality time out of work is not as expected.

Relate Link :  Error code blue screen on windows XP Part II
Error code blue screen on windows XP Print Spooler
Troubleshooting tips and techniques gathered printer.
Troubleshooting tips and techniques gathered printer part II
Troubleshooting tips and techniques gathered printer part III

  • Share/Bookmark
13 January, 2010

Troubleshooting tips and techniques gathered printer part III


Problem with the printer also has several issues that need a computer repairman problem. Troubleshooting the printer must know why and to resolve correctly to the printer to work again. Today I will talk about Troubleshooting tips and techniques gathered printer part III

Image on paper is trace overlap. This issue could only image includes text that appears on the print. First is no. If the paper is now available compression or SE does not match the box. When the paper feed to print it. Certainly in the position paper would not match or overlap with the groove. Make image or text lines overlap or are overlapped. The display will not meet with. The table only to see clearly, so time to enter the paper to check by.

Spaces lost on paper.

Sometimes you may encounter with a small gap. Missing text or images on different lines. This area lost will be no ink whatsoever. First check to see if the paper sheet is flat or not equal. Or is special printer paper not known or not? Try a new print with new paper sheet. If this does not mean changes have set Transfer Roller disruption or potential problems during the print. You must contact the Call Center of the printer brand.

Print documents but blank pages.

If you print documents, but in vain out the pages first to make sure that the printer feeds the paper out several sheets or not. Because if the paper be issued to each other so much. Sheets attached text may not blank paper first to drop out. In addition, if you buy a new machine. Do not forget to pull the plastic sheet off Otnenars out with no time like the type system will suck. Ink from the drum is not cool. If severe symptoms than it is possible that the control panel of ink may pay damages.

Printing a black line.

Ink emissions control panel fails. Ink can not control properly. This will go directly related to the control with the Laser Scanner remember to pull out more cartridges Otnenars disorders. That the cartridge may be damaged.

A linear bar code as text overlaps.

Print documents, but the line as long as a vertical bar code on the edge of the bottom edge next to the printer if you use long, but never change the drum or Otnenars no. Change has been recommended because it is the main cause of the symptoms that this. In addition, it may be a fraction of the ink powder to track such an important part. Laser scan lens. The paper feed roller before printing.

Relate Link : Error code blue screen on windows XP Part II
Error code blue screen on windows XP Print Spooler
Troubleshooting tips and techniques gathered printer.
Troubleshooting tips and techniques gathered printer part II
Troubleshooting tips and techniques gathered printer part IV

  • Share/Bookmark
11 January, 2010

Troubleshooting tips and techniques gathered printer part II

Problem with the printer also has several issues that need a computer repairman problem. Troubleshooting the printer must know why and to resolve correctly to the printer to work again. Today I will talk about Troubleshooting tips and techniques gathered printer part II

Print out the color channel. This condition has many causes, too. If the analysis simple. Is from the wrong paper type. Or excessive moisture in paper. Set out paper feed after printing ink into the skin texture roller. This device may direct any deterioration ครับ. This part is deeper than set laser control fails. As well as motor and gear drive or stumble across, which will result in the paper is feed into the wrong position or may move out. The paper has entered.

Printing out a good paper, but back dirty. Just not the type to rush out of your head or send it to more customers. If you have not turned the paper back to back because the vacuum could be stained by it. Fraction powder ink is at. This problem often is not anyone noticed between. You clean from secondary paper tray. The paper feeds in and out. Or the various roller. Ink powder that may be embedded in the crust.

Printing is too dark stem. Problem enough ink to fade and then. This time they try to find the print too dark to see what the line major cause of this problem comes from. Contact with the paper too. Czech to see what drum or disruption is not. As well as a key component Laser Scanner control panel may have a problem during print. If the read channel may have a significant amount of ink powder than is necessary. Exports to the paper.

Then print out any text wry twist. Printing a letter other wry twist or roll of paper even when the machine feed the paper out. To make sure that your paper type printers are supported or not? Photo paper specifically banned.Or shiny paper are. Based on a Aingcsehet to enter is strictly prohibited. In addition, if the air around the room or in the printer is set up to moisture or heat and may result in different printing systems. Working channel as well. Try punching Czech at the point.

Relate Link : Error code blue screen on windows XP Part II
Error code blue screen on windows XP Print Spooler
Troubleshooting tips and techniques gathered printer.
Troubleshooting tips and techniques gathered printer part III
Troubleshooting tips and techniques gathered printer part IV

  • Share/Bookmark
10 January, 2010

Troubleshooting tips and techniques gathered printer.

Printers are important computer peripherals another. Which serves to print documents quickly. When you use some time to tend to problems such as print does not print and then stop working, etc. The problem with the printer are several reasons. I concluded that today’s tips and troubleshooting with the following printers.

Printing a small scratch from time to time. If you print the document out and then found a small scratch line. At the edge of the paper in any one time before each is to assume that the primary cause of the Roller on the walking trails are stains, dirty paper. If the inspection was not found, try to check the cartridges Otnenars that is defective or not? Often the surface of the drum in Otnenars a small body. Make time print clue then be blamed on paper. Do not forget to check the type of paper you use as well.

Printing a small scratch from time to time

Printing the text is missing is the other. Or below the font is missing from time to time. Assumptions the first targeting the powder in the ink cartridge may be running out. Experience of the firm order page, paper copies may be dirty stains. And Otnenars own cartridges may be a fraction powder ink stains on soiled. Do not forget to visit the Czech Printer Properties that you are not already in the mode of printing with Eco Mode.
Print, but pressure has become fibrous.
Saw print, but a long line from time to time on some pages please? If they had each of your cartridges is running low. The reason may come from the hardware components as the surface of the drum is damaged or set of Fuser Film dirt stains, or what is to be located. Including those with obscure glass which reflects light in all this Scanner Set to clean immediately.

Printing the text is missing is the other. Or below the font is missing from time to time. Assumptions the first targeting the powder in the ink cartridge may be running out. Experience of the firm order page, paper copies may be dirty stains. And Otnenars own cartridges may be a fraction powder ink stains on soiled. Do not forget to visit the Czech Printer Properties that you are not already in the mode of printing with Eco Mode. Print, but pressure has become fibrous. Saw print, but a long line from time to time on some pages please? If they had each of your cartridges is running low. The reason may come from the hardware components as the surface of the drum is damaged or set of Fuser Film dirt stains, or what is to be located. Including those with obscure glass which reflects light in all this Scanner Set to clean immediately.

  • Share/Bookmark
06 January, 2010

Error code blue screen on windows XP Part II

Yesterday I’ve compiled error code blue screen and then some. Today I have added the error code blue screen yesterday.

8. (stop code 0X0000007B)Inaccessible Boot Device

  • Symptoms will often find the Windows boot process. A message that can not read the file system or boot partitions to make it normal or hard. Call Pat or wires to break into the hard disk or not. If they make a good regular boot.ini file may be lost or not they are running a multi OS to verify that the file may write config of OS differences.The other one caused this error is caused due to the upgrade windows while some devices are not compatible, try to remove unnecessary devices or think out a problem when upgrade windows gradually remove devices that have successfully put the problem back then installed. the latest drivers.

9. (stop code 0X0000007A) Kernel Data Inpage Error

  • This condition caused a problem with virtual memory system is Windows can not read or write data to the swapfile reason may be due to the hard disk bad sector, computer viruses, system error SCSI, RAM or a bad motherboard

10. (stop code 0X00000077) Kernel Stack Inpage Error

  • Problem. How to use Troubleshooting 9.

11.  (stop code 0X0000001E) Kmode Exception Not Handled

  • This symptoms of functional errors or service drivers with memory and IRQ, if a list of file or service represented on this error to uninstall the program or to roll back the drivers are. If an error stating that the file win32k cause of the control software from other companies. (Third-party) that do not use the Windows. That often occur with their Networking and Wireless is majority Error this may be another reason there is a run programs but not enough memory.

12. (stop code 0X00000079)Mismatched Hal

  • Symptoms of this work error Hardware Abstraction Layer (HAL) to understand before you HAL HAL is responsible for organizing the contact between the hardware with software. Software applications that applications which run on the device which is required to ้ example you have software that’s designed to use with Dual CPU motherboard with a Single CPU Windows will not. running a new solution is reinstall Windows. Another reason is the file name or Hal.dll NToskrnl.exe expired or has been modified to remove the Backup file or files to remove the original thought, or the latest version free of redundancy File copies of free software mail.

13. (stop code 0X0000003F)No More System PTEs

  • Caused by system Page Table Entries (PTEs) run by Virtual Memory Manager (VMM) running Windows errors made by PTEs, which is not necessary for Windows. Symptoms tend to occur on your working a multi monitors.

If you have this problem frequently. You can customize the following new PTEs have. 13.1. To open up editing the Registry to Start> Run and then type the command Regedit. 13.2. In accordance with this key HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Contro l \ Session Manager \ Memory Management. 13.3. To see the fire right pane, click PagedPoolSize. Put up the Value data to 0 and click OK. 13.4. SystemPages If you double-click the system-screen Multi Monitor to enter the Value data value 36000 or 40000 if the machine you put up a RAM 128 MB and up 110,000 in a case with more than 128 MB RAM, and then click OK. 13.5. Restart your computer. 14. (stop code 0X00000024) NTFS File System

  • Cause of the error report is Ntfs.sys Driver’s NTFS read and write errors. These include action cartoon. Performance error of IDE or SCSI controller running the program as a virus scan or free hard disk space. You can find details of any error. This by viewing the Event Viewer to open the way to go is start> run and type command to view eventvwr.msc Log file of the error, see the error of SCSI or FASTFAT section or System category in Autochk Application.

15. (stop code 0X00000050)Page Fault In Nonpaged Area

  • This causes the symptoms of the error of writing, editing data in RAM is to clean your legs, or try switching RAM or more RAM is a RAM test program to check the RAM bad or not.

16. (stop code 0Xc0000221)Status Image Checksum Mismatch

  • This condition caused by damage swapfile, including drivers with. Editing is like an 15.

17. (stop code 0X000000EA) Thread Stuck In Device Driver

  • Caused by the work of the machine will work in the Loop repeatedly. Together forever. Like to restart the round. Or notification error. What has not stopped up. This problem may be caused by the bug causes a program or a hundred other changes to try to follow this.
1. To see that your power supply enough power to pay the demands of the Company or not you see that your computer has more equipment to the power supply is not suitable for you is to ลื่ Union is very new to. up. Or check the computer parts that Capacitor motherboard to power the CPU that raising some swelling.
2. You see the video card that uses the latest drivers. Sure if the latest release and then also have to make it Rollback Driver prior to the issue.
3. Verify that the video card and motherboard or not such a bad burn, Wiring missing some pieces off the parts from the same location, etc..
4. See the bios that the VGA slot of select mode 4x, 8x is the Sepk card or not.
5. Check the motherboard manufacturers that are new drivers or if a New File to load into the new.
6. If you have a LAN card or your motherboard has on board is to disable function “PXE Resume / Remote Wake Up” by going off the BIOS.

17.1. To see that your power supply enough power to pay the demands of the Company or not you see that your computer has more equipment to the power supply is not suitable for you is to ลื่ Union is very new to. up. Or check the computer parts that Capacitor motherboard to power the CPU that raising some swelling. 17.2. You see the video card that uses the latest drivers. Sure if the latest release and then also have to make it Rollback Driver prior to the issue. 17.3. Verify that the video card and motherboard or not such a bad burn, Wiring missing some pieces off the parts from the same location, etc.. 17.4. See the bios that the VGA slot of select mode 4x, 8x is the Sepk card or not. 17.5. Check the motherboard manufacturers that are new drivers or if a New File to load into the new. 17.6. If you have a LAN card or your motherboard has on board is to disable function “PXE Resume / Remote Wake Up” by going off the BIOS. 18. (stop code 0X0000007F) unexpected Kernel Mode Trap

  • This condition is most players are symptoms overclock RAM data does not correlate to CPU CPU is running too fast. Or too hot.
  • Cause of the overclock solution is reduced down to a normal clock or a cooling of the CPU the most.

19. (stop code 0X000000ED)Unmountable Boot Volume

  • Symptoms that Windows does not find a hard drive. (Not the boot system) in case you have multiple hard drives. You may use one of Patrick’s lines, such as hard disk errors as Patrick 33MB/secound which requires 40 pin cable, but you’ll have the 80 pin to the representative.

20. (STOP 0×0000008e” error message during Windows XP setup

  • RAM using the RAM problem or put a new and incompatible hardware. Try changing the RAM to a new place or see the light does not pay regularly to try to change power supply.

Relate Link : Error code blue screen on windows XP Part Print Spooler
Troubleshooting tips and techniques gathered printer.
Troubleshooting tips and techniques gathered printer part II
Troubleshooting tips and techniques gathered printer part III
Troubleshooting tips and techniques gathered printer part IV

  • Share/Bookmark
05 January, 2010

Error code blue screen on windows XP


When Windows XP is a problem was often sent the blue screen error code to let you know why the problem occurred while running. This problem will be resolved in different ways. Today I made a summary error code blue screen and solution in each case as follows.

1. (stop code 0X000000BE) Attempted Write To Readonly Memory.

  • Due to a program or service or driver error, such as some files lost. Drivers of change between different versions to uninstall the program down before this problem. If the drivers have to roll back to older drivers or to find the latest drivers down. (If a newer) if their service is that we open the first problem is to conduct close or disable.

2. (stop code 0X000000C2) Bad Pool Caller

  • This error code is similar to 1 but if they focus on the hardware is different from Hardware upgrade their machines, such as ram, harddisk cards are not compatible with WindowsXP. workaround is to upgrade some equipment out if they need to. by Al Driver Software Update or the new device’s firmware. And warnings for the update to turn off anti-virus anti-virus program before it will see a virus.

3. (stop code 0X0000002E) Data Bus Error

  • Caused by transport of hardware called a BUS system damage, including RAM, cache L2 CPU, video card memory, hard disk, hard work to step error (too hot) and free motherboard.


4. (stop code 0X000000D1)Driver IRQL Not Less Or Equal

  • Drivers with IRQ (Interrupt Request) do not match. To approach problems as case 1.

5. (stop code 0X0000009F)Driver Power State Failure

  • Caused by power management systems with conflicting driver or service when you work for a Company “hibernate” solution if the Windows Driver error notification or service of which is to uninstall it or use the Rollback driver or shutdown management. Power of Windows.

6. (stop code 0X000000CE) Driver Unloaded Without Cancelling Pending Operations

  • Symptoms drivers off themselves though. AT commands are not Windows. Changes to make the same case 1.

7. (stop code 0X000000F2)Hardware Interrupt Storm

  • Caused by hardware devices such as USB or SCSI controller placement with IRQ errors caused by drivers or firmware changes as above 1.

Now I have error code blue screen to leave this much. Ask friends to follow instructions.

Relate Link : Error code blue screen son windows XP Part II

  • Share/Bookmark
21 August, 2009

sb5ap7kdxc

sb5ap7kdxc

  • Share/Bookmark
This blog is monetized using Are-PayPal WP Plugin Bindexed.com Alvz.com